Hydraulic Cable Deployed Pump With Water Jetting Agitator – 12 Inch
Model: 12-Inch JPH 12000 Cable Deployed Pump with Jetting Ring
- Hydraulic Pressure Gauge for pump circuit to operator (0-6000 PSI)
- Magnetic Flow meter to maintain stable plug free pipeline flow and maximize production
Required Equipment To Operate Attachment
- EDDY Pump circuit requirements from excavator auxiliary power OR from Hydraulic Power Unit 160-200 GPM at 5000 PSI (750cc motor)
- Jetting Ring Agitator. Water Pump Requirements, GPM 400-1000 at 150 PSI Max
- 12” material handling discharge hose and hydraulic lines plumbed out to the end of the boom
- Crossover check valve to prevent damage to hydraulic motor and prevent pump rotor from coming off
- Magnetic flow meter
- Discharge line pressure gauge (0-150 psi)
- “Quick Prime” Valve (requires small 24-volt air system)
- Pivot mounted Discharge hose carrier (adaptable to most machines)
- Cable Hung Unit Can Convert to be Compatible with Liner Safe Roller Attachment and Self Cleaning Mud Guard
- Recirculation system for pre-mixing applications (requires small 24-volt air system)
General Specs
The Cable Deployed Pump with Jetting Ring Agitator is a non-clog pump designed for high solids industrial pumping applications. Our patented pump technology outperforms all centrifugal, vortex and positive displacement pumps in a variety of the most difficult pumping applications. Increase or decrease water flow and adjust jetting pattern to suit your project demands
Available in alternative power options and pump sizes depending on your application.
| Production: 4000-7000 GPM or 500-600 cubic yards of material per hour | ||
| Head with 750cc hydraulic motor (23” rotor) 200 gpm oil @5000PSI | Up to 200 feet | Up to 60.96m |
| Overall Weight (without optional equipment) | 9,500 lbs | 4310 kg |
| Overall Length | 191 inches | 4.85 m |
| Overall Height | 60 inches | 1.5 m |
| Overall Width with discharge pipe removed | 58 inches | 1.17 m |
| Overall Width with discharge pipe mounted (right side) | 57 inches | 1.80 m |
| Carrier Weight Range | 30 + tons | 27,215+ kg |
| Standard Jetting Ring Diameter | 36 inches | 91m |
| Double seal with Sealed Barrier fluid tank (allow dry run) | 3.5 inches | 89 mm |
The Information contained in this drawing is the sole property of EDDY PUMP CORPORATION. Any reproduction in part or as a whole without the written permissoin of EDDY PUMP CORPORATION is Prohibited.
GPM & VELOCITY CALCULATION BASED ON 4″ CENTRIFUGAL WATER PUMP, 760 GPM WITH 81′ HEAD
| SIZE | JETS | PART # |
| EXF4K | 16 | 16025 |
| EXF6K, EXF8K, EXF10K | 28 | 12882 |
Pump & Dredging
EDDY Pump Deployment Options
Flooded Suction Pumps
The fluid to be pumped with flooded suction pumps is positioned above the pump. Flooded suction pumps typically require less priming effort because gravity assists in keeping the pump primed. With the pump positioned below, gravity can feed the fluid into the pump’s suction and keep the pump primed.
Read More ↗
Submersible Pumps
Pumps that are completely submerged in the liquid are called submersible pumps. By being submerged in the fluid to be pumped, there is no need for priming the pump.
Read More ↗
Self-Priming Pumps
With a self-priming unit, the pump and power unit are not submerged. The suction hose goes into the slurry and the unit acts like a super-sized wet dry vacuum. Can be trailer mounted for added mobility.
Read More ↗
Call for sales or support
If you need assistance with pump selection, sales or engineering support, call 619-404-1916.
EDDY Pump – JETTING RING HEAD SPEC SHEET
EDDY Pump – JETTING RING HEAD SPEC SHEET
Applications
Features and Benefits – 12 Inch HD 12000 Heavy Duty Slurry Pump
Applications
- Barge Unloading
- Deep Water Dredging
- Mining
- Sand & Agg
- Oil & Gas
- Fly ash & Coal Ash
Features and Benefits
- Non-Clog, High Viscosity, High
Specific Gravity, High Abrasives,
Low pH Pumping Design - Transport 40-70% Solids
- Ability to pump objects of up to 9-
inches in diameter
Applications
- Sludge
- Slurry
- Drilling Mud
- Mine Tailings
- Grit
- Sand Mixtures
Pump Curve
A pump curve is a graphical representation of a pumps ability to produce flow against a certain head. The science is matching a curve that is accurate for your project, leading to the proper pump selection and best efficiency. EDDY Pumps are primarily used for high solids, slurry, sludge, and dewatering.
We Pump Solids, Not Water
EDDY Pump – 12 Inch HD 12000 Heavy Duty Slurry Pump – Pump Curve
Operating Levels
| MIN FLOW | 1800 GPM |
|---|---|
| MAX FLOW | 7000 GPM |
| HEAD RANGE | Up to 200 ft |
| DISCHARGE SIZE | 12 inch |
| SUCTION SIZE | 14 inch |
| SOLIDS HANDLING | Solids up to 7 inches |
| MAX SPEED | 1800 RPM |
| PERCENT SOLIDS | Up to 40-70% Solids |
| CU YD MATERIAL HR | 500-600 |
| DREDGING DEPTH | Up to 100 ft |
Sales Quote With Custom Pump Curve
Do you know specifics about your project? Let us know and we can create your own personalized pump curve.
We are one of the few companies who manufactures both our pumps and dredging equipment to ensure optimal support.
HD (Heavy Duty) Slurry Pumps / Dredge Equipment
Related Products
For assistance Call 619-404-1916 and let us help match your project
with the right pump.